Gule Independent of the type of sources, for hardness there are two possibilities for the of the uncertainty. NOTE 1 For indentation diagonals less than 0, mm, the increase of the uncertainty has to be considered. The duration of the test force shall be 10 s to 15 s, except for tests on materials whose time-dependent properties would make this an unsuitable range. The correction factors are tabulated in terms of the ratio of the mean diagonal d of the indentation to the diameter D of the cylinder. For undated references, the latest edition of the referenced document including any amendments applies.
|Published (Last):||2 February 2011|
|PDF File Size:||18.97 Mb|
|ePub File Size:||20.34 Mb|
|Price:||Free* [*Free Regsitration Required]|
Meztiktilar The Amber document status indicator indicates that some caution needed when using this document — it is iiso Introduction to Materials and Materials Forming Next: Have you read this? Adobe is a trademark of Adobe Systems Incorporated. Because of this approach, it is important that the individual machine components are operating within the tolerances.
If not, an indirect ios should be performed. It makes it easy to scan through your lists and keep track of progress. Care should be taken, if standard uncertainties of type A and B are summarised, that the contributions are not counted twice see Clause 4 of GUM: Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing.
Your reading intentions are private to you and will not be shown to other users. Type Document Web address https: The correction factors are tabulated in terms of the ratio of the mean diagonal d of the indentation to the diameter D of the sphere.
If the measuring system fails this test, appropriate action should be taken. ISO consists of the following parts, under the general title Metallic materials — Vickers hardness test: NOTE There is evidence that some materials may be sensitive to the rate of straining which causes small changes in the value of the yield strength.
HV 2,5 24,52 N may be used. The finish of the surface shall permit accurate determination of the diagonal length of the indentation. Specifies the Vickers hardness test method, for the three different ranges of test force for metallic materials.
The correction factors are tabulated in terms of the ratio of the mean diagonal d of the indentation to the diameter D of the cylinder. There is no correction of the hardness values with respect to the error.
If two adjacent indentations differ in size, the spacing shall be based ido the mean diagonal length of the larger indentation. It is important that the test piece lies firmly on the support so that displacement cannot occur during the test. For dated references, only the edition cited applies.
Please log in to set a read status Setting a reading intention helps you organise your reading. It should be noted that for anisotropic materials, for example those which have been heavily cold-worked, there will be a difference between the lengths of the two diagonals of the indentation. NOTE 1 A strict comparison of hardness values is only possible at identical test forces. Due to the small depth of Vickers microhardness indentations, it is essential that special precautions are taken during preparation.
For automated measuring systems this standard should be applied accordingly. The error b step 10 can be expected to be a systematic effect. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. Figure 1 — Principle of the test The Vickers hardness is proportional to the quotient obtained by dividing the test force by the sloping area of the indentation, which is assumed to be a right pyramid with a square base, and having at the vertex the same angle as the indenter.
Such conversions, therefore, should be avoided, unless a reliable basis for conversion can be obtained by comparison tests. Free to use BIM project management tool provides step-by-step help to define, manage and validate responsibility for information development and delivery at each stage of the asset life cycle in level 2 BIM projects.
In this case, an estimate of type A standard uncertainty may be obtained from the statistical analysis of repeated indentations into the test piece. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.
Please log in to set a read status. Draft International Standards adopted by the technical committees are eh to the member bodies for voting. It is intended to make the annex normative in the next revision of this part of ISO Standard. TOP Related Articles.
BS EN ISO 6507-1
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Your reading intentions are also stored in your profile for future reference. There is no general process of accurately converting Vickers hardness into other scales of hardness or into tensile strength. The finish of the surface shall permit accurate determination of the diagonal length of the indentation. The correction factors are tabulated in terms of the ratio of the mean diagonal d of the indentation to the diameter D of the sphere. The Amber document status indicator indicates that some caution is needed when isso this document — it is either: Ihre Klassifizierung und Auswirkung auf iwo Messwerte.